Welcome to my blog phone parts › 2020年01月16日
2020年01月16日
3 Steps on How to Replace OnePlus 6 Rear Camera Lens Cover
The OnePlus 6 camera lens cover is easy to be scratched and broken. When this happened unfortunately to your phone, we suggest you replace it. It is not good to replace the camera lens cover directly on the back cover because it will leave fragment or fingerprint on the camera. Here we would like to demonstrate how to tear down the battery door and replace the camera lens cover in steps. Let’s check this below.
Step 1: Tear down the battery door
First of all, we should always remember to power off the phone and take out the SIM card slot. Use a hot air gun to blow the battery door on around the edge on 80 ℃ for 1-2 minutes for easy teardown, then use a suction cup and hard plastic plectrum to slice and separate the battery door. Flip over the battery door after it is entirely separated. Loosen the 10 Phillips screws and take off the bracket, then we may disconnect the fingerprint scanner sensor.
Step 2: Take off the Camera lens and replace the lens cover
After the OnePlus battery door is totally separated, we can move to the next step on camera lens cover replacement. Firstly, we use a hot air gun to blow the camera lens with 80℃ for 1 minute. After the glue is melted, use a spudger to push the camera lens cover out. Next, we use an ultra-thin plastic sheet to slice and separate the OnePlus 6 rear camera lens cover from the battery door. After the camera lens cover is removed, we have to clear out the glue on the battery cover. Glum the camera lens with B-7000 glue and place the new camera lens cover on it. Push it slightly and adjust the position.
Step 3: Reassemble the battery door
After the new camera lens cover is installed, we have to test the clarity of the new glass cover. Attach the battery door on the phone and turn on the phone. Turn on the camera and check the image on the screen. Make sure no dust, dirt or fingerprint on the camera. Then take off the battery cover, attach a new frame cover adhesive on the battery door. Connect the fingerprint scanner sensor flex cable and cover back the bracket. Fasten the 10 Phillips screws. The Last step, assemble the OnePlus 6 battery door and insert the SIM card tray. All process is done.
The whole process is simple as long as you are careful. Don’t take off the camera lens cover from the battery door directly because it will break the glass cover and leave fragments on the camera. If you are not confident about yourself, we suggest you go to the repair shop. Besides, you may also check the OnePlus 6 parts like OnePlus 6 LCD screen and digitizer assembly in our store. Leave your message to us if you have interests. Etrade Supply is here to help you.
Step 1: Tear down the battery door
First of all, we should always remember to power off the phone and take out the SIM card slot. Use a hot air gun to blow the battery door on around the edge on 80 ℃ for 1-2 minutes for easy teardown, then use a suction cup and hard plastic plectrum to slice and separate the battery door. Flip over the battery door after it is entirely separated. Loosen the 10 Phillips screws and take off the bracket, then we may disconnect the fingerprint scanner sensor.
Step 2: Take off the Camera lens and replace the lens cover
After the OnePlus battery door is totally separated, we can move to the next step on camera lens cover replacement. Firstly, we use a hot air gun to blow the camera lens with 80℃ for 1 minute. After the glue is melted, use a spudger to push the camera lens cover out. Next, we use an ultra-thin plastic sheet to slice and separate the OnePlus 6 rear camera lens cover from the battery door. After the camera lens cover is removed, we have to clear out the glue on the battery cover. Glum the camera lens with B-7000 glue and place the new camera lens cover on it. Push it slightly and adjust the position.
Step 3: Reassemble the battery door
After the new camera lens cover is installed, we have to test the clarity of the new glass cover. Attach the battery door on the phone and turn on the phone. Turn on the camera and check the image on the screen. Make sure no dust, dirt or fingerprint on the camera. Then take off the battery cover, attach a new frame cover adhesive on the battery door. Connect the fingerprint scanner sensor flex cable and cover back the bracket. Fasten the 10 Phillips screws. The Last step, assemble the OnePlus 6 battery door and insert the SIM card tray. All process is done.
The whole process is simple as long as you are careful. Don’t take off the camera lens cover from the battery door directly because it will break the glass cover and leave fragments on the camera. If you are not confident about yourself, we suggest you go to the repair shop. Besides, you may also check the OnePlus 6 parts like OnePlus 6 LCD screen and digitizer assembly in our store. Leave your message to us if you have interests. Etrade Supply is here to help you.
